反推装置对翼身融合分布式推进系统气动性能影响数值模拟

为了研究新型反推装置对翼身融合分布式推进系统气动性能的影响,将机身简化为二维模型,利用数值模拟的手段来研究攻角、反推开度,以及风扇打开或关闭对飞行参数的影响,为翼身融合分布式推进系统的反推装置设计提供初步的意见和建议。结果显示:反推闭合和风扇打开之后该机型的升力系数和俯仰力矩系数都会有较大增加;随着反推开度的增加,升力系数和俯仰力矩系数也随之增加;来流攻角对翼身融合分布式推进系统的气动性能也有较大影响。      

逆向进气复合角发散冷却孔流量系数试验

针对回流燃烧室外环壁面冷气与燃气流动方向相反的情况,试验研究了发散孔进气方向与环腔通道气流流动方向相反的条件下,复合角发散冷却孔流量系数随发散孔倾角(25°~55°)、偏角(90°~180°)及压降系数等参数的变化规律。研究结果表明:复合角发散孔的流量系数随倾角的增大而增大,随偏角的增大而减小；随着压降系数的增大,复合角发散孔的流量系数先呈近似线性增长,当压降系数大于0.95后,呈非线性增长且增长速度减缓。      

跨介质航行器波浪环境入水流场演变和运动特性研究

跨介质航行器是一种既可以在空中飞行又可以在水下潜航的新概念航行器,基于仿生学原理,提出一种通过改变外形实现水空介质跨越的航行器模型,通过入水试验装置和计算流体动力学方法,对航行器带攻角从空气到水的介质跨越过程进行了试验和数值仿真研究,得到了跨介质入水过程航行器的运动姿态和入水空泡形态,并通过数值仿真得到了航行器的升力、阻力、速度和加速度演化规律。同时基于数值模拟方法对有波浪情况和静水情况下航行器入水过程空泡演变以及运动特性进行对比。结果表明:提出的航行器构型在水中具有较好的姿态调整能力,波浪的有无和波高的不同都会对航行体入水运动特性造成影响。     

运载火箭推进剂复杂流动传热问题数值模拟中的模型简化方法

在运载火箭改进优化或新型运载火箭设计过程中,会遇到各种复杂的流动与传热问题。按照真实产品和物理过程直接建立的数值计算模型过于复杂,不同尺度的结构、流动与传热、长时间的飞行过程相互耦合,出现计算时间太长(数年)、收敛困难、程序调试困难等问题。针对初始条件复杂、飞行过程复杂、边界条件复杂3类具体问题,总结了3种相应的模型简化方法,分别是工程经验法、极限参数法、低维近似法,为推进剂复杂流动与传热的数值模拟提供参考。     

多机并联火箭羽流流场及其底部热环境分析

For the problem that the plume flow field structure of a multi engine parallel rocket is complicated and the bottom thermal environment is extremely harsh, which may cause the failure of the engine structural components, the plume flow field and thermal environment at different altitudes are studied through numerical simulation. The result is compared with the measured results in flight which shows that when the rocket is flying at a low altitude, the plume of the engines do not interfere with each other. As the flight altitude increases, the plumes gradually expand and begin to interfere with each other, and finally there is an obvious backflow at the bottom of the rocket. The maximum heat flux at the moment of take off is basically the same as the measured value in flight. Before the backflow occurs, the heat flux mainly consists of radiant heat, the convective heat flow increases as the flight altitude grows, but it is also much smaller than the peak heat flow at takeoff. The result has certain guiding significance for the optimal design of engine structure thermal protection.     

Near-wall topological patterns and flow structures over a simplified Danaus plexippus model

Studies on the high-lift mechanisms of butterfly gliding flights shed light on the design of the micro air vehicles. The flow field around a simplified Danaus plexippus model is investigated using the hydrogen bubble visualization and the Particle Image Velocimetry (PIV) techniques. There are three near-wall topological patterns with different Angles of Attack (AoAs): the separation bubble, the Leading-Edge Vortex (LEV) and the high AoAs flow. For the separation bubble pattern, two saddles and two foci form in the middle of the model. The features of the LEV pattern are the leading-edge separation lines. The topological characteristics of the separation lines are changed by the interaction between the LEV and the Wing-Tip Vortex (WTV). For the high AoAs flow pattern, four unstable foci are found at the forewing and the hindwing respectively. The angle between the trajectory of the WTV and the model increases with increasing AoA even though the slope of the WTV angle versus AoA curve declines at the moderate AoAs.     

Aerodynamic performance enhancement for flapping airfoils by co-flow jet

Introducing active flow control into the design of flapping wing is an effective way to enhance its aerodynamic performance. In this paper, a novel active flow control technology called Co-Flow Jet (CFJ) is applied to flapping airfoils. The effect of CFJ on aerodynamic performance of flapping airfoils at low Reynolds number is numerically investigated using Unsteady Reynolds Averaged Navier-Stokes (URANS) simulation with Spalart-Allmaras (SA) turbulence model. Numerical methods are validated by a NACA6415-based CFJ airfoil case and a S809 pitching airfoil case. Then NACA6415 baseline airfoil and NACA6415-based CFJ airfoil with jet-off and jet-on are simulated in flapping motion, with Reynolds number 70,000 and reduced frequency 0.2. As a result, CFJ airfoils with jet-on generally have better lift and thrust characteristics than baseline airfoils and jet-off airfoil when C_μ is greater than 0.04, which results from the CFJ effect of reducing flow separation by injecting high-energy fluid into boundary layer. Besides, typical kinematic and geometric parameters, including the reduced frequency and the positions of the suction and injection slot, are systematically studied to figure out their influence on aerodynamic performance of the CFJ airfoil. And a variable C_μ jet control strategy is proposed to further improve effective propulsive efficiency. Compared with using constant C_μ, an increase of effective propulsive efficiency by 22.6% has been achieved by using prescribed variable C_μ for NACA6415-based CFJ airfoil at frequency 0.2. This study may provide some guidance to performance enhancement for Flapping wing Micro Air Vehicles (FMAV).     

高主流湍流度下密度比对涡轮导叶全气膜冷却特性的影响

为了研究高主流湍流度下二次流密度比对涡轮导叶全气膜冷却特性的影响,使用热色液晶测量了在主流湍流度为15%,二次流密度比为1.0和1.5下三维涡轮导叶的气膜冷却效率和换热系数。二次流与主流质量流量比为7.0%和12.5%。结果表明:二次流密度比增大可以降低冷气射流的动量,小流量比工况下,在叶片前缘和压力面前半段,动量较低的二次流在高主流湍流度的影响下更易耗散,增大二次流密度比使冷却效率明显降低;大流量比工况下,二次流动量降低使气膜孔后区域冷气贴附性增强,气膜冷却效率和冷气覆盖效果均得到提升。小流量比工况下,二次流密度比增大对叶片表面换热的影响较小;大流量比工况下,二次流密度比增大使吸力面中弦区域和压力面后半段的平均换热系数比分别降低15%和25%。     

模块化永磁直线游标电机等效磁网络及漏磁分析

在模块化永磁直线游标电机的初始设计及优化设计中,使用有限元方法(FEM)计算漏磁系数时需要耗费大量的建模和计算时间。针对这一问题,建立该种电机的等效磁网络模型,在建模期间,考虑气隙中的边缘效应,并计算永磁体组与定子齿在不同相对位置时的等效磁导,得到该种电机在一个周期内不同相对位置时的漏磁磁导和漏磁系数的数学解析表达式。采用FEM验证了该数学解析表达式的准确性。研究结果为模块化永磁直线游标电机的设计提供了理论依据。     

回流燃烧室流动特性试验

为了揭示有/无燃烧状态下燃烧室热态和冷态流场的特征和流动特性，针对某型回流燃烧室单头部试验件，使用粒子图像测速仪（PIV），测量燃烧室燃烧状态下不同截面处的热态流场，以及没有燃烧状态下不同截面处的冷态流场，探讨不同总压损失系数对回流燃烧室热态/冷态流场特征及流动特性的影响。研究表明:随着总压损失系数的增大，冷态条件下各截面流场结构基本保持不变，如射流孔穿透深度、射流角度、回流区位置及大小、流线等基本保持一致，但是各位置点速度大小逐渐增大。热态条件下各截面流场随着总压损失系数增大，流场结构也基本保持不变；相同总压损失系数时，热态流场与冷态流场存在差异，燃油喷射与气流的相对运动将会对燃烧室头部的流场结构造成影响，速度较冷态流动时略微增大。